What’s cruising without a few bumps in the road?

We’ve been back in St. Kitt’s for a week and the boat is still not in the water. The boat work we’d asked to have done started the day before we arrived. We told them what we needed done last June when we dropped her off for storage, and again in November, and December, and earlier this month. Last January, the boat work we’d asked for started on the day we arrived, so I suppose this year is an improvement. Island time.The big job that needed doing, which Dave and I could not do, was the bottom copper coat. Dave is extremelyallergic to the hardener in this epoxy-based paint. Before we launched last January, Dave spoke to the then yard manager about the job and learned there is a guy on the island who does it as an outside contractor. We’d buy the supplies in St. Martin and bring them back with us in June, which we did. Dave met the guy in June, at the boatyard, to discuss the job; all seemed good. When November rolled around, nobody could get in touch with him. When we still hadn’t heard anything after Christmas, Dave contacted the yard owner who put Dave in touch with another guy who could do it, I’ll call him Bob. Dave and Bob texted back and forth and Dave said it sounded like Bob knew what he was doing, so told him to go ahead.

We’re pretty sure our boat is the first one Bob has copper coated. First, the hull needs to be sanded and smooth and any pits that don’t sand smooth need to be filled. Our hull is still pitted in places. The time-sensitive, epoxy-based copper coat requires a crew of 3-4 to do it well. Bob had one other guy working with him who was less than dedicated to the work. Finally, the hardened copper coat needs to be sanded smooth. Bob and the other guy showed up Monday with one battery powered sander, no way to recharge it, and not enough sandpaper. By Tuesday morning, with only about one quarter of the final sanding done, Dave suggested buying electric sanders and more paper. Away Dave & Bob went and returned with the needed supplies. That helped, because the sanding was finished this afternoon. In speaking with Dave daily, Bob has acknowledged throughout the process what he should have done differently. If he ever does this type of job again, we’re sure he’ll do it even better. Bob is a good worker and learns from his efforts. The other guy did a lot of sitting and half-hearted sanding. It stinks to have to pay $45/hour/person for amateur work, but pay we shall. 

On the upside, Dave and Bob bonded a little. On Friday, Dave had given Bob a spare solar panel we’d gotten for free but couldn’t use. When Dave bought the sanders, he told Bob he could keep one after the work was done. During their drive, they discovered a shared love of hunting. Bob hunts wild boar on the island, a lot of wild boar. He gifted us with 8 pounds of boar meat! We do meet some mighty nice folk on our travels.

 That was just one bump in the road.

Our windlass needed attention. (For you non-boaters, the windlass raises and lowers our anchor and chain). Dave came prepared with a rebuild kit. The job took longer than anticipated. Dave not only did the anticipated rebuild, but also a lot of correcting of things that were poorly done when it was initially built. The windlass had also been installed poorly, so he improved that before reinstalling it. I even got to play a role in this, doing a small epoxy repair job on the mounting base. Monday night, just after sunset, it was reinstalled and we tested it. As Dave punched the up and down buttons, the lights inside Lady flickered on and off. In addition, the anchor went down, but not back up. It also made some unfortunate, complaining sounds. There’s also a way to crank the gypsy (the part the chain links sit in) manually with a handle should the motor die, and that wasn’t working. Ack! By early Tuesday afternoon, Dave had it sorted. Our windlass works now!

The flickering lights during our windlass test, were the result of another bump in the road. Our 12V golf cart batteries run the house load of fridge, freezer, lights, stereo, dinghy lift and windlass. Their capacity was basically non-existent, so the windlass calling for all that power tanked them, causing the lights to go off. Dave had purchased two 12V car batteries last year, so he switched the wiring to those. They’re temporary, because their capacity is not as high as a that of healthy golf cart batteries. Unfortunately, nobody sells golf cart batteries on this island, so we’ll probably have to buy those in Guadeloupe.

Still with me? I have two more bumps to go.

Bump #4 was our replacement multifunction display (the chart plotter that allows us to set routes and navigate, see our speed and depth). The original started delaminating last year, which turned out to be a warranty issue. So last June Dave removed it, lugged it home, and shipped it back to Garmin who sent us a new, bigger and better replacement for free! Too bad they sent us the wrong model. We have front and side scan sonar transducers and a depth sounder. The multifunction display they sent does not have the proper ports for these. Depth is an important thing to know, especially when traversing or anchoring in shallow areas. Dave was able to connect the front scan sonar which can also serve as a depth reader. It’s not ideal, but if Garmin can’t (or won’t) ship the correct display to the Caribbean on their dime, the exchange will have to wait until we’re back in the U.S.

The final (for now) bump in the road was the theft of the gas can out of our dinghy. Had we not stupidly left the gas can in our dinghy, unlocked, it wouldn’t have been stolen. Mea culpa. Fortunately for us, the local Budget Marine store had one in stock. Off we went to Basseterre today to purchase said gas can and requisite attachments, as well as a couple of unrelated items we needed. This trip also provided us with the opportunity to eat at one of our favorite local restaurants, El Freddo. It wasn’t a bad way to spend a few hours today.

Upon our return to the boat yard this afternoon, we learned that the bottom work is finished, the power wash has been started and will be completed in the morning, and they can launch us tomorrow, although they have to schedule us around two other boats being launched. Bob needs about 2 hours while Lady is in the lift slings to copper coat the areas where she was resting on the jack stands. They won’t be able to be sanded smooth afterward, but it’s better than not having those areas coated at all. If all goes well, we should be in the water by late afternoon. They have an open slip at a rickety old dock that we can stay at for a night or two while we do our provisioning runs. 

Perhaps by the next time I post, we’ll be someplace more interesting. This season we hope to visit, in no particular order, Nevis, Montserrat, Dominica, Guadeloupe and Antigua. I will, of course, keep you posted. 

Until next time, stay safe and take care of each other!